El Camino is Spanish for "the road" or, alternatively, "the path", or quite literally, "the walk".
Ford Australia was the first company to produce a coupe utility as a result of a 1932 letter from the wife of a farmer in Victoria, Australia asking for “a vehicle to go to church in on a Sunday and which can carry our pigs to market on Mondays”. Ford designer Lew Bandt developed a suitable solution, and the first coupe utility model was released in 1934. Bandt went on to manage Ford’s Advanced Design Department, being responsible for the body engineering of the XP, XT, XW, and XA series Ford Falcon utilities. General Motors’ Australian subsidiary Holden also produced a Chevrolet coupe utility in 1935, but the body style did not appear on the American market until the release of the 1957 Ford Ranchero.
Both the coupe utility and the similar open-topped roadster utility continued in production, but the improving economy of the mid- to late-1930s and the desire for improved comfort saw coupe utility sales climb at the expense of the roadster utility until, by 1939, the latter was all but a fading memory.
The mid-1955 introduction of Chevrolet's Cameo Carrier pickup truck helped pave the way for the El Camino. Although it was a model variant of Chevrolet's light-duty pickup, the Cameo offered an array of car-like features that included passenger-car styling, fiberglass rear fenders, two-tone paint, a relatively luxurious interior, as well as an optional V8 engine, automatic transmission, and power assists. Other pickup truck producers, including Dodge, Ford, and International, began to offer flush-side cargo boxes on some of their 1957 models. However, Ford also introduced the 1957 Ranchero, and established a new market segment in the U.S. market of an automobile platform based coupe utility. In 1959, Chevrolet responded with the El Camino to compete with Ford's full-sized Ranchero. The El Camino and Ranchero would compete directly only in the 1959 model year.
First generation (1959–1960)Edit
The El Camino was introduced for the 1959 model year two years after the Ford Ranchero. Chevrolet stylists had considered a new coupe pickup well before the Ranchero appeared; according to stylist Chuck Jordan, Harley Earl himself had suggested such a thing back in 1952.
This was the year of the completely redesigned, longer, lower and wider full-sized Chevrolet. It sold in fewer numbers than the more conservatively styled Fords, but 22,246 El Caminos were sold, compared to Ford's 14,169 Ranchero. Like the Ranchero, it was based on an existing and modified platform, namely the new-for-1959 Brookwood two-door station wagon and corresponding sedan delivery variant; unlike those models, the El Camino was available any drivetrain option corresponding to the car line, but used a single trim level; the exterior used Bel-Air trim while the inside was trimmed like a low-end Biscayne. No other trim options were available from the factory, although 1959-60 El Caminos are often restored with Impala body mouldings and interiors. The El Camino was built on Chevy's 1959 passenger-car chassis that featured a "Safety-Girder" X-frame design and full-coil suspension, both of which had debuted on the 1958s. The 119-inch (3,000 mm) wheel-base was 1.5 inches (38 mm) longer than that of the 1958 models, though. Overall length for all 1959 Chevys was up to 210.9 inches (5,360 mm). The El Camino's payload rating ranged from 650 pounds to 1150 pounds, with gross vehicle weights ranging from 4400 to 4900 pounds, depending on powertrain and suspension options specified. The somewhat soft, passenger-car-type standard suspension enabled the El Camino to stand level without a load. (By contrast, the Ranchero came with stiffer heavy-duty rear springs that provided it with a standard 1100-pound payload rating and gave it a distinct "rake" when unloaded.) The quirky Level Air suspension option, in its second and final year, was listed as available, but was almost never seen on any Chevrolet model, much less an El Camino. The 1959 El Camino was promoted as the first Chevrolet pickup built with a steel bed floor instead of wood. The floor was a corrugated sheetmetal insert, secured with 26 recessed bolts. Concealed beneath it was the floor pan from the Brookwood two-door wagon, complete with foot wells. Box capacity was almost 33 cubic feet (0.93 m3).
The 283-cid Turbo-jet V8 with two- or four-barrel carburetion and several Turbo-Thrust 348-cid V8s with four-barrel or triple two-barrel carbs (the latter with up to 335 bhp (250 kW; 340 PS) by mid 1959) were among the entries. Even the 250- and 290-bhp 283-cube Ramjet Fuel Injection engines were available.
Hot Rod magazine conducted a test of an El Camino equipped with the hottest powertrain combination available in early 1959—a 315 bhp (235 kW; 319 PS), triple-carb, solid-lifter 348 V8 mated to a four-speed. HR testers clocked 0-60 mph times of around seven seconds, estimated top speed at 130 mph (210 km/h), and predicted 14-second/100-mph quarter-mile performance with a rear-axle ratio suitable for serious drag racing installed.
A total of 22,246 El Caminos were produced for 1959. That bested the count of 21,706 first-year Rancheros made in 1957 and the 14,169 Ford sedan pickups built in direct competition for the 1959 model year. But 1960 would be a different story. The similar but less flamboyant 1960 model started at $2366 for the six-cylinder model; another $107 for a V8 with the two-barrel 283. At first glance, the exterior once again had a Bel Air look, with that series' bright-metal "jet" appliqué and narrow trailing molding used to accent the rear quarters. Inside, Biscayne/Brookwood appointments also persisted. The seat was now covered in striped-pattern cloth with vinyl facings. Available interior trim shades were once again gray, blue, and green. Floor coverings were in medium-tone vinyl. Mid-1959 powertrain availability was carried over with minimal changes for 1960: The base 283-cid V8 was detuned a bit for fuel economy and was now rated at 170 bhp (127 kW; 172 PS), and the fuel-injected engines were officially gone.
Orders plummeted by a third, to just 14,163, at which point Chevrolet discontinued the model; meanwhile, Ford moved 21,027 Rancheros, which were now based on the brand-new Falcon compact. The pioneering American sedan pickups just did not connect with enough car-buying Americans. Perhaps these early "crossovers" didn't carry enough passengers; in a time when baby-boomer families dominated the market, three across was the best they could offer. The low-level trim and marketing efforts focused almost exclusively on commercial customers may have inhibited sales, as well.
Second generation (1964–1967)Edit
Chevrolet reintroduced the El Camino four years later based on the Chevrolet Chevelle. The 1964 model was identical to the Chevelle forward of the B-pillars and carried "Chevelle" and "El Camino" badges, but Chevrolet marketed the vehicle as a utility model and Chevelle's most powerful engines were not available. Initial engine offerings included six-cylinder engines of 194 and 230 cubic inches with horsepower ratings of 120 and 155, respectively. The standard V8 was a 283 cubic-inch Chevy small block with two-barrel carburetor and 195 horsepower (145 kW) with optional engines including a 220-horsepower 283 with four-barrel carburetor and dual exhausts. Added to the El Camino's option list during the course of the 1964 model year were two versions of the 327 cubic-inch small block V8 rated at 250 and 300 horsepower (220 kW) — the latter featuring a higher compression ratio of 10.5:1, larger four-barrel carburetor and dual exhausts.
The 1965 El Camino received the same attractive facelift as the '65 Chevelle, with a more pronounced V-shaped front end, and a higher performance version of the 327 engine rated at 350 hp (261 kW) that was also available in Chevelles under option code L-79 was made available. Most of the other engines were carried over from 1964, including the 194 and 230 cubic-inch Turbo Thrift sixes, the 195-horsepower 283 cubic-inch Turbo-Fire V8 and 327 cubic-inch Turbo-Fire V8s of 250 and 300 horsepower (220 kW). In 1966, GM added a 396 cu in (6.5 L) V8 engine to the lineup rated from 325 to 375 hp (280 kW). The 1965 327 would run low 15s in the 1/4 mile (at some 90 mph), while 1966 to 1969 models were easily into the mid- to upper-14s. New sheetmetal highlighted the 1966 El Camino, identical to the Chevelle forward of the B-pillars. A new instrument panel with horizontal sweep speedometer was featured. Inside, the standard version featured a bench seat interior and rubber floor mat from the lower-line Chevelle 300 series, while the Custom used a more upscale interior from the Chevelle Malibu with plusher cloth-and-vinyl or all-vinyl bench seats and deep twist carpeting, or optional Strato swivel bucket seats with console. A tachometer was optional. The 1967 El Camino followed the Chevelle's styling facelift with a new grille, front bumper, and trim. Air shocks remained standard equipment on the El Camino, allowing the driver to compensate for a load. The year 1967 also brought the collapsible steering column and options of disc brakes and Turbo Hydramatic 400 3-speed automatic transmission. It was the second year the 396 could be had in the El Camino (both 13480 300 Deluxe base and 13680 Malibu series). Since the L35 396/325 hp engine was the base for the SS396 series, the number of L35 engines reported sold by Chevrolet in 1967 (2,565) were sold in one of the two El Camino series since these were the only series the engine could be ordered in. Since the L34 (now 350 hp) & L78 (375 hp) were available in either El Camino series as well as the two SS396 body styles, there is no way of knowing how many of these optional engines went to which body style. Chevrolet does report 17,176 L34 and 612 L78 engine options were sold in 1967 Chevelles, but there is no breakdown of body styles. The TH400 3-speed automatic was now available as an option (RPO M40) with the 396 engine in both the SS396 series and the 396-equipped El Caminos. The 3-speed manual transmission remained the standard transmission with a heavy duty (RPO M13) also available along with the 2-speed Powerglide and either M20 wide ratio or M21 close ratio 4-speed transmissions.
Third generation (1968–1972)Edit
Chevy introduced a longer El Camino in 1968, based on the Chevelle station wagon/four-door sedan wheelbase (116 in (2,946 mm), overall length: 208 in (5,283 mm)); it also shared Chevelle Malibu exterior and interior trims. The interior was revamped including cloth and vinyl or all-vinyl bench seats and deep twist carpeting. All-vinyl Strato bucket seats and center console were an $111 option. Power front disc brakes and Positraction were optional. A new, high-performance Super Sport SS396 version was launched. The Turbo-Jet 396 had 325 bhp (242 kW) or 350 bhp (260 kW) versions. Returning to the official options list for the first time since late 1966 was the 375 bhp (280 kW) L78. It had solid lifters, big-port heads, and an 800 cfm Holley four-barrel on a low-rise aluminum manifold. A three-speed manual was standard with all engines, and a four-speed or automatic was optional. In 1968, the SS was a separate model (the "SS-396"). Therefore, it can be identified by the vehicle identification number (VIN). For example, a 1968 El Camino with a VIN starting with "13880" would be a genuine SS-396 model, while a 1968 El Camino with the VIN "13680" would be a non-SS "Malibu" version of the El Camino. All genuine Super Sports from 1966-1968 have an "8" as the third digit of the VIN; 1968 is the only year for the El Camino SS as a separate model.
The 1969 models showed only minor changes, led by more-rounded front-end styling. A single chrome bar connected quad headlights, and a slotted bumper held the parking lights. New round instrument pods replaced the former linear layout. For the first time, the Chevrolet 350 V8 was used in an El Camino. The Super Sport group included a 265- or 325-horsepower 396-cubic-inch V8 beneath a double-domed hood, along with a black-out grille displaying an SS emblem. More potent editions of the 396 engine, developing 350 or 375 horsepower (280 kW) also made the options list. Options included power windows and locks.
The 1970 models received sheet metal revisions that gave the bodies a more squared-up stance, and interiors were also redesigned. The new SS396, which actually displaced 402 cu in (6.6 L) (although all emblems read 396) was available. Chevrolet's largest and most-powerful engine of the time was also put into a select few El Caminos. The LS6 454 CID engine, rated at 450 hp (336 kW) and 500 lb·ft (680 N·m) of torque, gave the El Camino 1/4-mile times in the upper 13-second range at almost 105 mph (169 km/h). The 1971 El Camino got fresh front-end styling that included large Power-Beam single-unit headlights, a reworked grille and bumper, and integral park/signal/marker lights. For 1971, mandated lower-octane unleaded fuel necessitated a reduction in engine compression, and GM's A.I.R. system, a "smog pump", was added to control tailpipe emissions. Power and performance were reduced. Engine offerings for 1971 included the 250-6, small-block V8s of 307 and 350 cubic inches; and big block V8s of 402 and 454-cubic-inch displacements. Horsepower ratings of those engines for 1971 ranged from 145 for the six to 365 for the RPO LS5 454 – all in gross figures. The LS6 454 V8 was gone forever. A rebadged El Camino, the GMC Sprint debuted in 1971. It shared the same engine and transmission offerings as its Chevrolet counterpart.
The 1972 El Caminos wore single-unit parking and side marker lights on their front fenders, outside of a revised twin-bar grille, but little changed. For 1972, horsepower measurements were switched to the "net" figures as installed in a vehicle with all accessories and emission controls hooked up. Engine offerings included the 110 horsepower (82 kW) 250-6, a 307 V8, a 175 horsepower (130 kW) 350-cubic-inch V8, and big block V8s of 402 and 454 cubic-inch displacements. The 402-cubic-inch (still known as a 396) produced 240 horsepower (180 kW); the 454 managed to put out 270 horsepower (200 kW) under the net rating system. Super Sport equipment could now be ordered with any V8 engine, including the base 307-cubic-inch version. All 1972 SS models have a "W" as the fifth digit in the VIN.
Fourth generation (1973–1977)Edit
For 1973, the El Camino was redesigned. Matching the Chevelle line and using the wagon chassis, it was the largest El Camino generation. Energy-absorbing hydraulic front bumper systems created an ungainly appearance on these vehicles and added more weight. There were two different trim levels of El Caminos during this period. The base model and SS option shared interior and exterior appointments with the Chevelle Malibu, while the El Camino Classic (introduced for 1974) shared its trim with the more upscale Chevelle Malibu Classic. The chassis design was as new as the bodies with 1-inch (25 mm) a wider wheel track, front and rear. The left wheel was adjusted to have slightly more positive camber than the right, which resulted in a more uniform and stable steering feel on high-crown road surfaces while maintaining excellent freeway cruise stability. Clearances for spring travel were also improved for a smoother ride over all types of surfaces; the coil springs at each wheel were computer-selected to match the individual car's weight. Front disc brakes were now standard on all '73 El Caminos. Additional new features were an acoustical double-panel roof, tighter-fitting glass, flush-style outside door handles, molded full-foam seat construction, flow-through power ventilation system, inside hood release, refined Delcotron generator and sealed side-terminal battery, a larger 22-US-gallon (83 L; 18 imp gal) fuel tank, and "flush and dry" rocker panels introduced first on the redesigned 1971 full-size Chevrolets. New options included swivel bucket seats (with console) and Turbine I urethane (backed by steel) wheels, as was the instrument gauge cluster. A benefit of the new body designs was much better visibility of which the unusually thin windshield pillars contributed. A structural improvement was a stronger design for the side door guard beams. The 307 2-barrel V8 of 115 hp (86 kW) was the base engine. Options included a 350 2-barrel V8 of 145 hp (108 kW), a 350 4-barrel V8 of 175 hp (130 kW), and a 454 4-barrel V8 rated at 245 hp (183 kW). Hardened engine valve seats and hydraulic camshafts made these engines reliable for many miles, and allowed them to accept the increasingly popular unleaded regular gasoline. The three-speed manual transmission was standard; 4-speed manual and Turbo Hydra-Matic 3-speed automatic transmissions were optional. Crossflow radiators and coolant reservoirs prevented overheating. 1973 El Camino SSThe SS, now a trim option, included a black grill with SS emblem, bodyside striping, bright roof drip moldings, color-keyed dual sport mirrors, special front and rear stabilizer bars, rally wheels, 70-series raised white-lettered tires, special instrumentation and SS interior emblems. The SS option was available with a 350 or 454 V8 with the 4-speed or Turbo Hydra-Matic transmissions.
The 1974 El Caminos sported an elongated, Mercedes-type grille. Inside, the new top-of-the-line El Camino Classic featured luxurious interiors with notchback bench seats (or optional Strato bucket seats) upholstered in cloth or vinyl, carpeted door panels and woodgrain instrument panel trim. The 350 V8 became the base engine and a 400 V8 engine was new this year. The 454, the top engine, was available with the Turbo Hydra-Matic 400 automatic or 4-speed manual transmission.
The 1975 models featured a new grill, providing a fresh appearance. Suspension upgrades offered a quieter ride, and radial-ply tires became standard. Dual remote mirrors, new twin sport mirrors, intermittent wipers, and cruise control were among new convenience features this year. The 1975 high energy ignition (HEI) provided spark to the spark plugs with minimal maintenance and increased power. The larger distributor cap also provided better high-RPM performance by decreasing the likelihood of the spark conducting to the wrong terminal. The 250-cubic-inch in-line six of 105 hp (78 kW) was offered as the base engine. The 454-cubic-inch V8, downrated yet again to 215 horsepower (160 kW), made it into 1975 as an El Camino option, but this would be its last go-around. It was not available in California, and the optional four-speed stick was no longer offered. Buyers could now choose an Econominder instrument package that included a vacuum gauge to point out when optimum fuel economy was being attained. For 1976, El Camino Classic models now featured the new rectangular headlights that other high-end GM cars were sporting. These were quad units in stacked arrangement. The base model retained the previously used dual round headlights. Engines included the base 250 I6 engine, a new 140-horsepower 305-cubic-inch V8, two- and four-barrel 350s (with availability still depending on California delivery), and the 400-cubic-inch V8, still good for 175 hp. All engines except the 250 I6 came with the Turbo Hydra-matic automatic transmission as the only transmission available. The 250 I6 came with a 3-speed manual or an optional Turbo Hydra-matic.
The 1977 models were little changed, except the 400 V8 was gone. The El Camino Classic was again the top model and the SS option continued.
Fifth generation (1978–1987)Edit
The 1978 through 1987 El Caminos were produced in four trim levels: Classic, Black Knight(1978)/Royal Knight(1979–83), Conquista and Super Sport, and shared chassis components with the Chevrolet Malibu. Chevrolet 90° V6 and Buick V6 engines were used for the first time. The optional 305 cubic-inch small block V8 was rated at 150 or 165 horsepower (123 kW), and from 1982–1984, the Oldsmobile-sourced Diesel engine was also optional. A new, trimmer El Camino was unveiled in 1978, adopting the new, more sharp-edged Malibu styling, and a one-inch longer wheelbase of 117 in (2,972 mm). The front end sheet metal was shared with the Malibu, the doors with the Monte Carlo, and the rear tailgate and bumper was shared with the Malibu station wagon. For the first time, though, the El Camino had a unique chassis - it was shared with no other Chevrolet. The front end featured a new single rectangular headlight design. The base engine was a 200-cubic-inch (3.3-liter) V6 that developed 95 horsepower (71 kW). Three upgrades could be ordered: a 231-cubic-inch V6 developing 105 horsepower (78 kW), or a 305-cubic-inch V8 with 145 horsepower (108 kW). Only El Caminos (and Malibu station wagons) could get the 170-horsepower 350-cubic-inch V8. It was not available on Malibu passenger cars. Among GM makes, at least, the era of bigness was fading into history, overtaken by a new age of efficiency and economy.
The 1979 model got minimal changes following its debut as a redesigned "new-size" model in 1978. Alterations to the 1979 El Camino amounting to little more than a new divided grille. However, a "small-block" 267-cubic-inch (4.4-liter) V8 joined the options list and slotted between the standard 3.3-liter V6 and the optional 5.0-liter four-barrel V8. The 350-cubic-inch (5.7-liter) V8, developing 170 horsepower (130 kW) was again available. Both three- and four-speed manual transmissions had floor shifters.
The 1980 El Camino started out the 1980s with few changes, though engine choices were shuffled a little. The base V6 displaced 229 cubic inches, up from 200 the year before. Horsepower increased from 94 to 115. Optional again were a 267-cubic-inch V8 with 125 horsepower (93 kW) and a 305 V8, now with 155 horsepower (down five). The 350 with 170 horsepower (130 kW) offered in 1979 was dropped. A three speed floor shifted manual transmission was standard, but most got the optional three-speed automatic.
The 1981 models received a new vertical grill. The 1981 engines mostly continued from 1980, but now used GM's Computer Command Control (CCC) emission system. The base 229-cubic-inch V6 made 110 horsepower (down from 115), as did the California-only 231-cubic-inch Buick V6. Optional engines were the 267-cubic-inch V8 with 115 horsepower (86 kW) and The 305-cubic-inch V8, now with 150 horsepower (110 kW). The three-speed automatic added a lock-up torque converter to aid highway mileage. The 1982 (through the final 1987) El Camino sported a frontal appearance with a crosshatch grille flanked by quad rectangular headlights. New under the hood for 1982 was a 105-horsepower 5.7-liter (350-cubic-inch) Diesel V8, which was also offered in Chevy's full-size cars. Though mileage with the diesel was commendable, it was an expensive option and would eventually amass a dismal repair record. Gasoline-engine choices were unchanged, except Chevy's 229-cubic-inch (3.8-liter) V6 was now standard in California-bound cars, replacing Buick's 231-cubic-inch V6.
In 1983, the 4.4-liter V8 was gone, leaving the 5.0-liter version as the only optional gas V8. The standard engine was again Chevy's 3.8-liter V6 with 110 horsepower (82 kW), though California cars, once again, got a Buick V6 with similar specifications. Continuing on the options list was the 5.7-liter V8 Diesel with 105 hp (78 kW). The sister Malibu sedan and wagon were discontinued after the 1983 model year.
The 1984-87 El Camino SS was offered as a conversion (completed by Choo-Choo Customs Inc., of Chattanooga, Tennessee) to include the aerodynamic front end similar to the Monte Carlo SS, but did not receive the L69 engine package. For 1985, GM shifted El Camino production to Mexico, and the new 4.3 L was standard through 1987.
Australia, Mexico, South Africa and Middle EastEdit
General Motors manufactured and marketed "utility" coupe-pickup models in Australia as early as the mid 1930s. These Aussie "utes" typically combined the styling of a five-window coupe body with an integrated pickup box. GM's export organization offered a Chevrolet utility as late as 1952. In Mexico, the El Camino was sold as the Chevrolet Conquistador. In South Africa and later Middle East, rebadged Australian Holdens were sold, including the Holden Commodore utility as the Chevrolet El Camino and later the Chevrolet Lumina ute. GM Holden still produces a ute in Australia.
El Camino todayEdit
El Caminos can usually be found at car shows in the muscle car category. Early models can be found as restored originals or hot rods with modified engines, mag wheels and custom paint. Some are used in various racing venues, and more can be spotted being used as daily drivers. The late 60s versions command the highest prices and inspire the most replicas from Hot Wheels, Matchbox and Johnny Lightning. The Discovery Channel program Monster Garage once turned an El Camino into a Figure-8 racer (dubbed the "Hell-Camino"). The drift team Bubba Drift uses a 1986 El Camino as the only drifting truck.
Like its Chevelle counterpart, the El Camino SS models with big-block V8s are prized by collectors. Of particular interest (and with correspondingly high collector value) is the 1970 SS454 model with the optional 450-bhp, 454 cubic-inch LS6 V8.
For years, GM has been rumored to be considering bringing back the El Camino. GM already has a vehicle ready in Australia in the form of the Holden Ute (a Chevrolet-badged version of which, known as the Lumina Ute, is sold in South Africa and Middle East), save for some minor changes necessary to make it available in the U.S.
This may have been backtracked within the past couple of years, however, as the Subaru Baja, the only "pickup car" recently available in the US, did not sell well at all and was dropped after the 2006 model year. On the other hand, the Baja's slow sales probably had less to do with the body style, and more to do with the poor fuel economy offered by it's AWD layout: fuel prices had increased dramatically around the same time it was discontinued.
In 1974, Chevrolet's sister division, Pontiac, reportedly took an El Camino body and grafted on the urethane-nose front end from its Grand Am series and added the GA's instrument panel and Strato bucket seats with recliners and adjustable lumbar support along with Pontiac's Rally II wheels as a styling exercise for a possible Pontiac version of the El Camino; the concept, however, never reached production. During the 1995 model year, GM had a concept El Camino based on the full-size Caprice station wagon using the grille of a 1994-96 Impala SS; this concept was destined for production, but was terminated due to GM's profitable SUV sales.
The Pontiac G8 ST was shown at the New York International Auto Show in March 2008. Based on the Holden Ute, it was built on the same G8 platform with a 73-inch (1,900 mm) cargo bed. The Sport Truck had the same 361 hp (269 kW), 6.0-liter V8 used in the G8 GT, as well as the 3.6-liter, 300 hp (220 kW) direct-injection V6. The G8 ST, slated for release as a 2010 model, was to be GM's first coupe utility in North America since the El Camino was discontinued in 1987. In January 2009, GM announced to dealers the G8 ST was cancelled due to budget cuts and restructuring. GM was speculated, in 2011, to be considering bringing back the El Camino under the Chevrolet brand as early as 2015.